Posiflex-business-machines PP7700 Series User Manual

Rev.: Original Aura PP7700 Series Wireless POS Thermal Printer User's Guide IMPORTANT!!!! Please read carefully before

1 - 6 • Do not use thermal paper containing Sodium (Na+), Potassium (K+) and Chlorine (Cl-) ions that can harm the print head thermal elements. •

2 - 1 II. QUICK START-UP A. LOADING PAPER 1. Desk Top Application 1. Slide the hood lock toward the front of the printer to release the hood.

2 - 2 2. When To Replace Paper Whenever the printer gives paper out signal or a red line appears on the thermal paper, it is the proper timing for

2 - 3 connection supports a genuine virtual cable connection thus supports the application software to use even the so-called direct I/O method fo

2 - 4 2. At the host system that the Dongle is connected, be sure to terminate any application program or to uninstall any driver occupying the COM

2 - 5 In “Hardware Update Wizard” that appears after this, choose “Install from a list or specific location (Advanced)” --> “Don’t search, I wi

2 - 6 Ignore this message and click “Next”, a warning dialogue box will pop up. Select “Continue Anyway” to exit the “Hardware Installa

2 - 7 Click Finish to close the wizard. Check that in “Device Manager” the “Communications Port” should be changed to “Posiflex Wireless Dongle” to

2 - 8 setup procedure since this BT ID could mean lengthy and hard to memorize by heart to average people. 3. At the host system that the Dongle is

2 - 9 COM port of the Dongle as if they were physically connected. In other words, you may now send all command / data to the COM port with Dongle

P/N: 19300900010 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with t

2 - 10 be carried out consecutively while unfortunately at the same time another print job is sent from another terminal, without the exclusive func

2 - 11 the power while the “Feed” button is pressed can prepare PP7700 for the signal detect operation. Now in the host Posiflex POS system, please

2 - 12 When the printer is used as a kitchen printer and a kitchen bell is prepared, please use this port for kitchen bell connection instead. 5.

2 - 13 font table will be printed in text mode again. To exit the test printing, please turn the printer off and on again. C. SP

2 - 14 Slightly release the fixing screw to adjust the position of sensor head. The acceptable paper roll bobbin outer diameter is between 18 and 22

2 - 15 accessory of the printer. If the user uses narrower paper roll and requires more spacer plates, it can be purchased from Posiflex. 4. Paper

3 - 1 III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the cover. • The areas around the

3 - 2 Before putting back the paper roll for printing, alcohol solvent must be dried completely. D. TROUBLE SHOOTING This section gives solutions t

3 - 3 If there is no paper jam and the print head is not overheated, turn off the printer and wait for half a minute then turn it back on. If the p

i Table Of Contents GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1

3 - 4 3. Paper Jam Problems Paper is jammed inside the printer – Turn off the printer and open the print hood by releasing the hood lock. Remove th

3 - 5 5. Graphic Printing Speed The RS232 protocol for printer Dongle connection defaults to 19200 bps. However, this setting could appear i

3 - 6 printed in two parts from two rolls of paper but every item will be printed. Printer fails to respond such as being powered off: -- The wirele

3 - 7 7. Advanced Analysis Tool This printer supports Hexadecimal Dump for experienced user to view exactly what data is received by the printer.

4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Printing speed 180 mm /sec. Maximum P

4 - 2 C. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 250 V AC INPUT FREQUENCY 50 ~ 60 HZ INPUT CURRENT 1.5 A MAX. @ 115 V AC OUTPUT

5 - 1 V. TECHNICAL INFORMATION A. INTERFACES 1. Wireless Interface Wireless Features Specification ITEM SPECIFICATION Frequency Band 2.4 ~ 2.48

5 - 2 2. Peripheral Interface The connector for peripheral control is a 6P6C RJ11 jack with the following pin assignment. The best recommended cash

5 - 3 change the switch setting when necessary. The switch position counting starts from the nearest edge of printer. The ON direction points to th

ii Spacer Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 14 Paper Cutting . . . . . . . . . . . . . . . . . . . . . . . . . . 2

5 - 4 sure that your software will take care of enough paper feed for the paper jam prevention issue. For switch position 8, when it is set to ON in

5 - 5 guide adaptor for use with the paper roll of 58 mm width, the switch should be set to ON in PP7700. Switch position 3 is usually set to OFF f

5 - 6 Hexadecimal codes are: 1B 6F Printer beeps when this command is received per condition set by beep definition. GS ‘o’ m: Beep definition (0 &l

5 - 7 when cash drawer is opened. n = ‘1’ (31H) applies to drawers giving a “short” signal when drawer is opened. Any value of the parameters outsi

5 - 8 The user may visit our web at http://www.posiflex.com.tw or http://www.posiflex.com for a view of the fonts in the code pages and character se

1 - 1 I. GETTING STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading; low noise; high resolution; light w

1 - 2 reminder function to persons around. It can be used to drive a separately purchased kitchen bell for such reminder function in noisy environm

1 - 3 • Language to add to standard model: Japanese Kanji; Korean; Traditional Chinese or Simplified Chinese E. MAIN PARTS ON THE EXTERIOR

1 - 4 Bottom View F. INDICATORS • Power LED: green • Error LED: red • Paper Out LED: red G. OPERATING ENVIRONMENT • Place the printer

1 - 5 • Try to prevent as much as possible any obstacle between printer and host PC such as metal plate, wire mesh or any other materials of meta